Inquiry


3+N产品应用

產品介紹

请点选下方产品蓝图

应用案例

电源与控制应用

产品面涵盖大功率电源、模组式电源、机架式式电源、控制器等产品线,主要是提供客户大功率系统电源管理或多组电源系统应用解决方案

CSP-3000 series
RST-7K5 series
NTN-5K+CMU2E
SHP-30K series
SHP-30K series
SHP-10K series

NTN-5K series

RST-10000 series

SHP-10K series

RCP-1U series+ RSP-1600 series

NMP-1K2 series

SHP-10K

The picture below shows the illustration of the synchrotron of TPS for which it mainly consists of Linear Accelerator (LINAC), Booster Ring and Storage Ring. The source produces the particles which are propelled up to speed in a LINAC before they are injected into a booster ring to be accelerated further. The particle beams then enter the storage ring, which maintains their speed. In case particle beams are diverted at speeds close to the speed of light, it emits part of the energy as synchrotron radiation in the form of electromagnetic waves.  Depending on requirements, the super bright beams are then diverted into the beamline to perform the experiment or application in the end station. RF amplifier system is to compensate the power loss of the particle beams in the storage ring due to the emission of synchrotron radiation by which a signal picked up on ring can be amplified and fed back in on the opposite side of the ring at a dedicated phase angle. The feedback loop helps to reduce the size and energy distribution. MEAN WELL system power solution is installed and applied as the DC power source for the RF amplifier system in the storage ring.

灯控与智能建筑应用

产品面涵盖DALI、KNX产品线,产品涵盖LED驱动器、执行器/调光器、总线电源、控制器、输入装置等,主要是提供客户一站式灯控与智能建筑应用解决方案

节能与绿能应用

产品面涵盖充电器、逆变器、双向电源等产品线,主要是提供客户节能、绿能、充电、储能相关应用解决方案



Burn-in is the process by which components of a system are exercised before being placed in service and often time prior to the system being completely assembled from those components. This testing process will force certain failures to occur under supervised conditions so an understanding of load capacity of the product can be established. The intention to carry out burn-in test is to detect those particular components that would fail as a result of the initial, high-failure rate portion of the bathtub curve of component reliability. If the burn-in period is made sufficiently long (and, perhaps, artificially stressful), the system can then be trusted to be mostly free of further early failures once the burn-in process is complete.  To fulfill this kind of requirement, numbers of high wattage equipment will participate in this situation, therefore, with the flexibility of MEAN WELL's system power, users are able to overcome and achieve a ALL in ONE BI system by its functionality.

Burn-in is the process by which components of a system are exercised before being placed in service and often time prior to the system being completely assembled from those components. This testing process will force certain failures to occur under supervised conditions so an understanding of load capacity of the product can be established. The intention to carry out burn-in test is to detect those particular components that would fail as a result of the initial, high-failure rate portion of the bathtub curve of component reliability. If the burn-in period is made sufficiently long (and, perhaps, artificially stressful), the system can then be trusted to be mostly free of further early failures once the burn-in process is complete.  To fulfill this kind of requirement, numbers of high wattage equipment will participate in this situation, therefore, with the flexibility of MEAN WELL’s system power, users are able to overcome and achieve a ALL in ONE BI system by its functionality.
10668